sync config with SKR E3 example
some values from: config\examples\BigTreeTech\SKR Mini E3 1.2
This commit is contained in:
parent
2d8a1de53b
commit
11ff943771
|
@ -531,9 +531,9 @@
|
|||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
#define DEFAULT_bedKp 10.00
|
||||
#define DEFAULT_bedKi .023
|
||||
#define DEFAULT_bedKd 305.4
|
||||
//#define DEFAULT_bedKp 10.00
|
||||
//#define DEFAULT_bedKi .023
|
||||
//#define DEFAULT_bedKd 305.4
|
||||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from pidautotune
|
||||
|
@ -542,6 +542,10 @@
|
|||
//#define DEFAULT_bedKd 1675.16
|
||||
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
#define DEFAULT_bedKp 50.71
|
||||
#define DEFAULT_bedKi 9.88
|
||||
#define DEFAULT_bedKd 173.43
|
||||
|
||||
#endif // PIDTEMPBED
|
||||
|
||||
// @section extruder
|
||||
|
@ -561,7 +565,7 @@
|
|||
* Note: For Bowden Extruders make this large enough to allow load/unload.
|
||||
*/
|
||||
#define PREVENT_LENGTHY_EXTRUDE
|
||||
#define EXTRUDE_MAXLENGTH 200
|
||||
#define EXTRUDE_MAXLENGTH 600
|
||||
|
||||
//===========================================================================
|
||||
//======================== Thermal Runaway Protection =======================
|
||||
|
@ -1220,7 +1224,7 @@
|
|||
#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
|
||||
|
||||
// Set the number of grid points per dimension.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_X 5
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
// Probe along the Y axis, advancing X after each column
|
||||
|
@ -1230,7 +1234,7 @@
|
|||
|
||||
// Beyond the probed grid, continue the implied tilt?
|
||||
// Default is to maintain the height of the nearest edge.
|
||||
//#define EXTRAPOLATE_BEYOND_GRID
|
||||
#define EXTRAPOLATE_BEYOND_GRID
|
||||
|
||||
//
|
||||
// Experimental Subdivision of the grid by Catmull-Rom method.
|
||||
|
@ -1453,7 +1457,7 @@
|
|||
|
||||
#define PREHEAT_2_LABEL "ABS"
|
||||
#define PREHEAT_2_TEMP_HOTEND 240
|
||||
#define PREHEAT_2_TEMP_BED 0
|
||||
#define PREHEAT_2_TEMP_BED 110
|
||||
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
|
||||
|
||||
/**
|
||||
|
@ -1708,7 +1712,7 @@
|
|||
//
|
||||
// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
|
||||
//
|
||||
//#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
|
||||
//
|
||||
// SPEAKER/BUZZER
|
||||
|
|
|
@ -953,7 +953,7 @@
|
|||
//#define LCD_TIMEOUT_TO_STATUS 15000
|
||||
|
||||
// Add an 'M73' G-code to set the current percentage
|
||||
//#define LCD_SET_PROGRESS_MANUALLY
|
||||
#define LCD_SET_PROGRESS_MANUALLY
|
||||
|
||||
// Show the E position (filament used) during printing
|
||||
//#define LCD_SHOW_E_TOTAL
|
||||
|
@ -1046,23 +1046,23 @@
|
|||
* - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
|
||||
* - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
|
||||
*/
|
||||
//#define SDCARD_SORT_ALPHA
|
||||
#define SDCARD_SORT_ALPHA
|
||||
|
||||
// SD Card Sorting options
|
||||
#if ENABLED(SDCARD_SORT_ALPHA)
|
||||
#define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
|
||||
#define FOLDER_SORTING -1 // -1=above 0=none 1=below
|
||||
#define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
|
||||
#define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
|
||||
#define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting.
|
||||
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||||
#define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#define SDSORT_CACHE_NAMES true // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
|
||||
#define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
|
||||
// Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
|
||||
#endif
|
||||
|
||||
// This allows hosts to request long names for files and folders with M33
|
||||
//#define LONG_FILENAME_HOST_SUPPORT
|
||||
#define LONG_FILENAME_HOST_SUPPORT
|
||||
|
||||
// Enable this option to scroll long filenames in the SD card menu
|
||||
#define SCROLL_LONG_FILENAMES
|
||||
|
@ -1150,7 +1150,7 @@
|
|||
*
|
||||
* :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
|
||||
*/
|
||||
//#define SDCARD_CONNECTION LCD
|
||||
#define SDCARD_CONNECTION ONBOARD
|
||||
#endif
|
||||
|
||||
#endif // SDSUPPORT
|
||||
|
@ -1374,7 +1374,7 @@
|
|||
#define BABYSTEP_MULTIPLICATOR_Z 1 // Babysteps are very small. Increase for faster motion.
|
||||
#define BABYSTEP_MULTIPLICATOR_XY 1
|
||||
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
|
||||
// Note: Extra time may be added to mitigate controller latency.
|
||||
|
@ -1415,7 +1415,7 @@
|
|||
#define LIN_ADVANCE
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
//#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
|
||||
#define LIN_ADVANCE_K 0 // Unit: mm compression per 1mm/s extruder speed
|
||||
#define LIN_ADVANCE_K 0.0 // Unit: mm compression per 1mm/s extruder speed
|
||||
//#define LA_DEBUG // If enabled, this will generate debug information output over USB.
|
||||
#endif
|
||||
|
||||
|
@ -1543,7 +1543,7 @@
|
|||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
|
@ -1575,7 +1575,7 @@
|
|||
#if ENABLED(SDSUPPORT)
|
||||
#define BLOCK_BUFFER_SIZE 32 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
|
||||
#else
|
||||
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
|
||||
#define BLOCK_BUFFER_SIZE 32 // maximize block buffer
|
||||
#endif
|
||||
|
||||
// @section serial
|
||||
|
@ -1724,12 +1724,12 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 30 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 5 // (mm) Initial retract.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 15 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 400 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
|
@ -1738,7 +1738,7 @@
|
|||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 350 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
|
|
Loading…
Reference in New Issue